A. Polit, R. Jez
ABB Corporate Research Center, Krakow, Poland
The air gap is one of the most crucial part of magnetic circuits, especially in high-power inductors. It significantly modifies the parameters of magnetic devices by increasing the saturation current, linearizing B-H curve of magnetic circuit and causing a decreasing in the inductance. Therefore the optimal selection of shape and dimensions of the air gap is very important from the design point ...
O. Vogel, and J. Ulm
Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...
M. Puskarczyk, R. Jez 
ABB Corporate Research Center, Krakow, Poland
Multilayer planar transformers are widely implemented in power electronic applications. The design process of these elements is complicated due to the complexity of a magnetic circuit and high frequency interactions between windings. Additionally, an analytical approach to the analysis (based on mathematical formulas) can be uncertain. The applied FEM method of the analysis can be a solution to ...
Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
T. Karmokar, R. Pietsch
HIGHVOLT Prüftechnik Dresden GmbH, Dresden, Sachsen, Germany
The computation of electric field strength is the state-of-the-art technique for designing and optimizing High-Voltage (HV) equipment. In this research, the equipment under analysis is Cable Termination (CaTr) which is used to apply high-voltage (75 kV – 800 kV AC) on the cable to be tested (Figure 1). The CaTr is based on the principle of linear electric field control using deionised water with ...
INP Greifswald e.V., Greifswald, Germany
2D self-consistent nonequilibrium model of a free-burning arc in argon has been developed. The model is based on the COMSOL Multiphysics® platform and describes in a self-consistent manner the fluid dynamics, the heat transfer, the magneto-electrodynamics, and species conservation. The governing equations are solved applying the COMSOL Multiphysics® interfaces Laminar flow, Electric Currents, ...
K. Falkowski, K. Sibilski
Wroclaw University of Technology, Wrocław, Poland
In the paper will be presented the construction of passive magnetic suspension with superconductors. The system of magnetic suspension was designed for GBRIEL project. There is presented numerical test bench of passive magnetic suspension with superconductor. This kind of suspension was selected for generation of magnetic levitation forces in a sledge of take-off and landing system of an ...
University of Manchester, Manchester, UK
This report mainly discusses the implementation and results of a project proposal, “Modelling using Finite Element Methods”. The report is devoted to implementation, which is a model of an electromagnet. The software tool that is used to model the electromagnet is COMSOL Multiphysics®, a commercial FEA package provided by the University of Manchester, Computer Science School. Additionally, the ...
S. C. Hegde
VIT University, Vellore, Tamil Nadu, India
The coaxial cable is one of the most commonly used bandwidth limited signal transmission line.Dispersion is a signal distortion phenomenon which arises due to frequency dependence of phase velocity of signal components. This phenomenon was explained through time domain approach by studying time taken by signals of various frequencies to propagate through the cable, which eventually may cause ...
Military University of Technology
The article presents the process of verification of the passive magnetic bearing by the Comsol Multiphysic program. There is shown construction of the radial passive magnetic bearing PMB60x85x20-5, which was designed in the Military University of Technology. The distribution of the magnetic flux density and the static characteristic of the bearing were estimated by the Comsol Multiphysic. The ...